3D Printer Repair Services for Dental Clinics
|
⭐ We are an authorized service center for SprintRay 3D printer repair. Your warranty stays intact, repairs use genuine OEM parts, and our technicians are certified directly by SprintRay. |
All Models, Common Issues & Our Repair Services
The table below covers every dental 3D printer and post-processing unit we service, listed from oldest to newest within each brand.
|
Brand |
Models (Oldest → Newest) |
Common Issues We Fix |
Our Repair Services |
More |
|---|---|---|---|---|
|
🔵 SprintRay — Authorized Repair Center |
||||
|
SprintRay 3D Printers |
Pro S → Pro 2 / Midas |
• Build platform not detected
• Resin tank RFID not reading
• Wi-Fi dropping during prints
• Optical panel misalignment
• Touchscreen unresponsive
• Resin tank not seating properly
• Cartridge jammed or not recognized
• Light engine not curing parts |
✔ Platform sensor repair
✔ RFID reader fix
✔ Network module repair
✔ Optical panel calibration
✔ Display repair
✔ Resin tank & cartridge fix
✔ UV module replacement |
|
|
SprintRay Post-Processing |
ProWash S →NanoCure |
• Wash pump not working
• Drying fan not turning on
• Fluid sensor giving false readings
• UV lamps are degrading, parts stay tacky
• Chamber overheating and shutting off
• Control panel unresponsive |
✔ Pump motor replacement
✔ Fan & heating element fix
✔ Sensor recalibration
✔ UV LED replacement
✔ Thermal sensor repair
✔ Control board repair |
|
|
🟠 Formlabs |
||||
|
Formlabs 3D Printers |
Form 3B → Form 4BL |
• Laser not curing fully
• Resin tank chip not detected
• Build platform adhesion failing
• Wiper arm moving erratically
• Printer losing cloud connection
• Z-axis or peel mechanism stuck
• Touchscreen showing errors
• Large-format panel edge inaccuracy |
✔ Laser / LPU module repair
✔ Tank chip & contact fix
✔ Build platform service
✔ Wiper latch & motor repair
✔ Firmware & network fix
✔ Dashboard update
✔ Panel calibration |
|
|
Formlabs Post-Processing |
Form Wash → Form Cure L V2 |
• Wash motor seized, basket not moving
• IPA level sensor showing empty
• Lid seal cracked, vapour leaking
• UV LEDs partially failed, uneven curing
• Turntable motor stalled
• Heating element not reaching the required temperature |
✔ Wash motor replacement
✔ Fluid sensor recalibration
✔ Lid seal & gasket fix
✔ UV LED bank replacement
✔ Turntable drive repair
✔ Heating element service |
|
|
🟢 Asiga |
||||
|
Asiga 3D Printers |
MAX UV → Ultra |
•positioning drift, layers uneven
• UV LED degrading, calibration alarms
• FEP vat film failing, prints sticking
• Z-axis backlash visible lines on tall prints
• Software not detecting the printer on the network
• DLP projector uneven light
• IR heating fault on newer Ultra models |
✔ SPS™ motor & encoder recalibration
✔ UV LED & radiometer reset
✔ FEP film replacement
✔ Z-axis lead screw repair
✔ Network & firmware fix
✔ DLP projector cleaning/swap
✔ IR heating element repair |
|
|
🟣 NextDent by 3D Systems |
||||
|
NextDent 3D Printers |
NextDent LCD1 → NextDent 5100 |
• LCD panel degrading, slow prints
• Auto-calibration failing on startup
• Resin vat film is going cloudy
• Resin tray not seating or locking
• Cloud / remote diagnostics link lost
• Figure 4® membrane clogging issues |
✔ LCD panel replacement
✔ Auto-calibration reset
✔ Vat FEP film replacement
✔ Tray lock actuator repair
✔ Firmware update & cloud re-pairing
✔ Figure 4® membrane service |
|
|
🩵 Dental Curing Machines, All Brands |
||||
|
All Brands (Curing Units) |
LC-3DPrint Box → Form Cure L V2 |
• UV lamps / LEDs degrading parts, not curing
• Turntable not rotating during the cure cycle
• Chamber overheating and shutting down
• Heating element not reaching temperature
• Control panel or timer unresponsive
• Door interlock sensor not triggering |
✔ UV lamp / LED bank replacement
✔ Turntable motor & belt repair
✔ Thermal sensor & fan repair
✔ Heating element replacement
✔ Control board & display repair
✔ Door interlock switch fix |
|
Not sure what's wrong? Ship it to us. Diagnosis is always free. |
Dental Curing Machines Repair
If your curing machine is not working right, every single part it processes is at risk, including crowns, night guards, surgical guides, clear aligners, and dentures. Under-cured or over-cured appliances do not fit properly and can harm patients. That is why curing machine repair is just as important as printer repair.
At Repair. Dental, we fix all major dental curing machines used in clinics and labs. Our repairs are fast, affordable, and backed by a warranty.
|
Curing Machines We Repair
• ✅ Formlabs Form Cure / Form Cure L V2 : Repairs for heating, rotating, and UV curing failures
• ✅ SprintRay Pro Cure / NanoCure : Troubleshooting digital display, LED array, and software bugs
• ✅ Asiga Flash / Asiga Cure : UV intensity issues, timer malfunctions, and power failures
• ✅ Ackuretta CURIE : Circuit board and touch panel repairs
• ✅ NextDent LC-3DPrint Box : Light consistency and curing cycle restoration
• ✅ Otoflash G171 : Flashlamp replacement, casing repair, and system diagnostics
• ✅ Creality Wash & Cure Plus : Fixing curing performance and mechanical issues
No matter the model, we provide curing machine repair that is fast, efficient, and affordable. |
Each Curing Machine, What Goes Wrong & How We Fix It
Here is a quick breakdown of the most common problems we see with each curing machine, and exactly what our repair covers.
|
🟠 Formlabs Form Cure & Form Cure L V2 | Form Cure → Form Cure L V2 (latest) |
|
|
Common Issues:
• UV LEDs are partially failing , parts that cure unevenly across the turntable
• Turntable motor stalling , parts sit still during the full cure cycle
• Heating element not reaching the set temperature
• Control display freezing or showing errors
• Form Cure L V2: heating inconsistencies in larger chamber |
What We Fix:
• UV LED array replacement, zone by zone
• Turntable drive motor and belt repair
• Heating element and thermocouple replacement
• Control board repair or swap
• Full post-repair output test before return
|
|
🟢 Asiga Flash & Asiga Cure | Asiga Flash → Asiga Cure (current) |
|
|
Common Issues:
• UV lamp intensity dropping , cured parts fall outside validated specs
• Door interlock sensor failing , unit will not start even with the door shut
• Timer board fault , cycle runs too long or cuts off too early
• Power failure , unit not turning on
• Reflector degradation , uneven UV distribution inside the chamber |
What We Fix:
• UV lamp and reflector replacement
• Door interlock micro-switch repair
• Timer board repair or replacement
• Power supply diagnosis and fix
• Curing output verified against Asiga validated specs after repair
|
|
🔴 Ackuretta CURIE | CURIE (current model) |
|
|
Common Issues:
• Circuit board failure , the unit shows an error or will not start
• Touch panel unresponsive, cannot set time or temperature
• UV output inconsistency in parts curing at different hardness levels
• Power supply fault, unit powering off unexpectedly |
What We Fix:
• Main circuit board repair or replacement
• Touch panel repair or swap
• UV output calibration and lamp check
• Power supply diagnosis and fix
|
|
⚡ Otoflash G171 | G171 (current model) |
|
|
Common Issues:
• Flashlamp burning out, no light output during the cure cycle
• Casing cracked or damaged, unsafe to operate
• System not starting or stopping unexpectedly
• Counter or timer display malfunction
• Internal reflector clouding, uneven curing |
What We Fix:
• Xenon flashlamp replacement
• Casing repair or protective cover replacement
• System diagnostics and control board repair
• Counter display fix
• Internal reflector cleaning or replacement
|
|
🩶 Creality Wash & Cure Plus | Wash & Cure Plus (current) |
|
|
Common Issues:
• Curing platform motor not rotating
• UV LEDs are weak or partially dead, uneven, or slow curing
• Wash pump not circulating IPA properly
• Touch panel not responding
• Timer or cycle settings not saving |
What We Fix:
• UV LED repair or replacement
• Rotation motor and drive mechanism fix
• Wash pump motor replacement
• Touch panel repair
• Full mechanical and curing output test after repair
|
We also repair legacy systems and models from other major brands. If your equipment is not listed here, simply contact us for support.
Common Issues Across All Curing Machines
No matter which brand or model you own, these are the most common curing machine problems we repair daily:
• UV lamps or LEDs are losing power over time , and parts come out soft or tacky
• Turntable or rotation motor stopping , parts only cure on one side
• Overheating and unexpected shutdowns, thermal protection kicking in
• Heating element failure: chamber not reaching the right temperature
• Control panel or touchscreen freezing, cannot start or adjust the cycle
• Door or lid sensor failing, the machine will not start even when closed properly
• Timer or cycle faults cause running too short or going on forever
|
If your curing machine is giving you any of these problems, do not keep using it. An underpowered curing unit can ruin expensive 3D printed parts without you realising it, and some materials have specific cure requirements tied to patient safety certifications. |
How to Get Your Printer or Curing Machine Repaired.Free & Fast
We've thought carefully about every step of the repair experience. Our goal isn't just to fix your printer but to make the whole process so simple and stress-free that you barely notice your device has gone.
|
STEP 1 |
Request your free shipping label at Repair.Dental. via call, WhatsApp, email, or visit Repair.Dental to initiate your repair. For international clients, we provide competitive guidance on express shipping. |
|
STEP 2 |
Pack your printer securely. Drop it off at UPS. No couriers to chase, just drop it off, OR you can schedule a pickup at your convenience. |
|
STEP 3 |
Our technicians run a full diagnosis the same day in most cases. You get a detailed written estimate. You approve it before any work begins. |
|
STEP 4 |
We repair your printer using genuine OEM parts where available, run calibration and performance testing, and ship it back fast. Most repairs take 2 to 3 days in standard cases and 3 to 5 days in complex cases |
|
STEP 5 |
Your repaired printer arrives with a model-specific warranty, a full repair report, and post-repair support. |
Why Choose Repair.Dental?
• Over a decade of dental equipment expertise
• Certified in Formlabs, SprintRay, Asiga, and NextDent printer repairs
• Authorized SprintRay service center , the highest standard of care for your printer
• Cost-effective solutions for curing machines and 3D printers
• Friendly support and worldwide service
• Trusted by dental labs and clinics across the world
Customer Success Stories
“Our SprintRay Pro S went down on a Monday morning with a full week of cases booked. By Thursday, it was back, fully repaired, and printing perfectly. Best repair service we have ever used for dental equipment.”
Dr. K.M. — General Dentist, Ontario
“Free shipping both ways and a free estimate — I was honestly skeptical. But they delivered exactly what they promised. No hidden costs, no drama, fast turnaround. We now send all our dental equipment repairs here.”
Dr. P.L. — Prosthodontist, Texas
“As a multi-location practice, printer downtime is incredibly costly. Repair. Dental’s fast turnaround and reliable service have made them our exclusive repair partner for all three locations.”
Dr. Maya R. — Practice Owner, Montreal
How We Compare to the Competition
|
Feature |
Repair.Dental |
Local Shops |
Manufacturer Service |
Winner |
|---|---|---|---|---|
|
All Major Brands Covered |
Yes |
Limited |
OEM Only |
Repair.Dental |
|
Authorized SprintRay Center |
Yes |
No |
Manufacturer |
Tie |
|
Curing Machine Repair |
Yes — 7 Units |
Sometimes |
Rarely |
Repair.Dental |
|
Free Estimate & Diagnostics |
Yes |
Often Charged |
No |
Repair.Dental |
|
Worldwide Shipping |
Yes |
Not Available |
Sometimes |
Repair.Dental |
|
Warranty on All Repairs |
Yes |
Not Always |
Yes |
Tie |
|
Turnaround Time |
2-3. days |
Varies |
2–3 Weeks |
Repair.Dental |
|
No Fix, No Charge |
Yes |
Rarely |
No |
Repair.Dental |
Frequently Asked Questions
Q: What 3D printer brands do you repair?
A: We repair Formlabs, SprintRay, Asiga, and NextDent by 3D Systems, plus dental curing machines.
Q: Are you an authorized SprintRay repair center?
A: Yes! Repair. Dental is an authorized service center for SprintRay 3D printer repair. Our technicians are factory-trained and use genuine SprintRay parts, keeping your warranty fully intact.
Q: Do you repair the new Form 4B / Form 4BL from Formlabs?
A: Absolutely. We repair all Form series printers, including the latest Form 4B (2024) and Form 4BL with LFD technology.
Related Blog Posts
|
Ready For Repair?
Free diagnosis • No obligation • model-specific warranty • Worldwide service
Start Your Free Repair Request at Repair.Dental
|
||
|
📞 Call Us
+1 855 533 3399
Mon–Fri, 9:00 am–5:30 pm EST |
Live Tech Support
Instant Response |
🌐 Online
Repair.Dental
|
|
Repair.Dental | The Global Standard in Intraoral Scanner Repair |
||
